TABLE OF CONTENTS
- Quick Reference
- What's in the Box
- Vacuum Mode
- Air Blower Mode
- Speed Controls
- Performance by Speed
- Battery & Charging
- Battery Indicators
- HEPA Filter & Dust Bin Cleaning
- Safety
- Still stuck?
Quick Reference
| Feature | Details |
|---|---|
| Product | Mopcop X |
| Product Code | POR 3660 |
| Type | 2-in-1 Cordless Vacuum & Air Blower |
| Suction Power | Up to 19,000Pa |
| Motor | Dual Brushless Motor |
| Motor Speed | Up to 87,000 RPM |
| Speed Modes | 3 |
| Battery | 3 × 2000mAh |
| Charging | Type-C, 5V/2A |
| Charging Time | Approx. 3 hours |
| Filter | Washable HEPA + Metal Mesh |
| Runtime | Approx. 55 / 33 / 13 min by speed |
What's in the Box
| Item | Quantity |
|---|---|
| Mopcop X | 1 |
| Nozzles | 5 |
| Type-C Charging Cable | 1 |
| User Manual | 1 |
Vacuum Mode
Make sure the Power Switch is ON.
Install the HEPA filter and metal mesh correctly.
Attach the required vacuum nozzle to the front side.
Press the Gear button to select the required speed.
Use the cleaner to collect dust, crumbs and small particles.
Air Blower Mode
Make sure the Power Switch is ON.
Attach the required blower nozzle to the back side.
Press the Gear button to select the required speed.
Use the airflow for narrow corners and hard-to-reach areas.
Speed Controls
| Button B Press | Result |
|---|---|
| 1st press | Speed 1 |
| 2nd press | Speed 2 |
| 3rd press | Speed 3 |
| 4th press | OFF |
The Power Switch must be ON before using the Gear button.
Performance by Speed
| Speed | Runtime* | Suction | Blower Speed |
|---|---|---|---|
| 1 | Approx. 55 min | Approx. 4.2 kPa | Approx. 29,000 RPM |
| 2 | Approx. 33 min | Approx. 7.2 kPa | Approx. 43,500 RPM |
| 3 | Approx. 13 min | Approx. 19 kPa | Approx. 87,000 RPM |
*Runtime figures can vary with usage.
Battery & Charging
| Item | Details |
|---|---|
| Battery | 3 × 2000mAh |
| Charging Port | Type-C |
| Charging Input | 5V/2A |
| Charging Time | Approx. 3 hours |
Battery Indicators
| Indicator | Meaning |
|---|---|
| Last bar flashing | Low battery |
| Bars lighting progressively | Charging |
| All 5 bars steady | Fully charged |
Mopcop X cannot be used while charging.
HEPA Filter & Dust Bin Cleaning
Remove the HEPA filter assembly from the dust cup.
Empty the collected debris.
Separate the HEPA filter cover from the filter.
Clean the filter cover with a soft brush.
Wash the HEPA filter and dust bin with water.
Allow all parts to dry completely.
Reassemble the filter and metal mesh before use.
Safety
Keep hands away from the air inlet and outlet.
Do not block the air inlet/outlet during use.
Keep away from water, heat and flammable substances.
Do not use with wet hands.
Do not insert objects into the air inlet/outlet.
Stop using the device if it makes unusual noise/smell or overheats.
Do not open or disassemble the product.
Still stuck?
If the issue persists after performing all troubleshooting steps, please raise a support request.
Our support team will assist you further.
Support
Visit: www.portronics.com
Support Portal: support.portronics.com
Was this article helpful?
That’s Great!
Thank you for your feedback
Sorry! We couldn't be helpful
Thank you for your feedback
Feedback sent
We appreciate your effort and will try to fix the article